Problem of plane stress state of two-layer body in dynamic elastic-plastic formulation
DOI:
https://doi.org/10.32347/tit.2022.51.0303Keywords:
Plane, stress, impact, composite material, armed material, reinforced material, elastic-plastic, deformationAbstract
Composite materials are widely used in industry and everyday life. Many different methods are used to calculate and develop composite materials. Many methods of calculation and design of such materials are successfully used. In this article, for the design of composite and reinforced materials, a technique for solving dynamic contact problems in more precise an elastic-plastic mathematical formulation is used. To consider the physical nonlinearity of the deformation process, the method of successive approximations is used, which makes it possible to reduce the nonlinear problem to a solution of the sequences of linear problems. The problem of a plane stress state (PStS) of a beam made from the composite reinforced double-layered material is being solved in dynamic elastic-plastic mathematical model. The reinforced or armed material consists of two layers: the upper (first) thin layer of solid steel and the lower (second) main layer of glass. This composite base is rigidly attached to an absolutely hard half-space. Rigid adhesion of the layers to each other is assumed. Glass is a very strong and very fragile material at the same time. The fragility of glass is due to the fact that there are many microcracks on the surface, and when a load is applied to the glass surface, these microcracks begin to grow and lead to the destruction of glass products. If we glue or immobilize the tops of microcracks on the surface, we will get a strong reinforced armed material that will be lighter, stronger and not subject to degradation of material properties such as aging, corrosion and creep. The impact process was modelled as a non-stationary plane stress state problem with an even distributed load in the contact area, which changes according to a linear law. The fields of the Odquist parameter and normal stresses were studied and compared to corresponding results of plane strain (PSS) problem with the same material of layers, same their thickness and size of the contact area. The upper reinforcing layer of metal or steel can be applied to the glass surface so that metal or steel atoms penetrate deeply, fill microcracks and bind their tops. The top layer can be quite thin.
References
Bogdanov V.R. (2008). Determination of frac-ture toughness of a material based on numerical modeling of the plane stress state. Bulletin of Kyiv National University. Series of Physical and Mathematical Sciences, Kyiv, No.3, 51-56 (in Ukrainian).
Bogdanov V.R., Sulym G.T. (2013). Modelling the growth of plastic deformations during impact based on the numerical solution of the problem of a plane stress state, Vestnik Mos-kovskogo Aviatsionnogo Instituta, Vol.20, Iss.3, 196-201 (in Russian).
Bogdanov V.R., Sulym G.T. (2010). The crack growing in compact specimen by plastic-elastic model of planar stress state. Bulletin of University of Kyiv, Series Physics & Mathematics, No.4, 58-62 (in Ukrainian).
Bogdanov V.R., Sulym G.T. (2010). Dynamic growing of a crack in a compact specimen ac-cording to the elastic-plastic model of the plane stress state. Bulletin of the Kyiv National University. Phys.-math. Series Sciences, Kyiv No.4. 51-54 (in Ukrainian).
Bogdanov V. (2022). Problem of plane strain state of two-layer body in dynamic elastic-plastic formulation (Part I). Underwater Technologies, Kyiv, No.12, 3-14. DOI:10.32347/uwt.2022.12.1101.
Bogdanov V. (2022). Problem of plane strain state of two-layer body in dynamic elastic-plastic formulation (Part II). Underwater Tech-nologies, Kyiv, No.12, 15-23. DOI:10.32347/uwt.2022.12.1102.
Bogdanov V. (2022). Problem of plane strain state of two-layer body in dynamic elastic-plastic formulation (Part III). Transfer of Inno-vation Technologies, Kyiv, No.12, 3-14. DOI:10.32347/tit.2022.51.0302
Lokteva N.A., Serduk D.O., Skopintsev P.D., Fedotenkov G.J. (2020). Non-stationary stress-deformed state of a composite cylindrical shell. Mechanics of Composite Materials and Struc-tures, 26(4), 544-559, DOI:10.33113/mkmk.ras.2020.26.04.544_559.08 (in Russian).
Igumnov L.A., Okonechnikov A.S., Tarlakov-skii D.V., Fedotenkov G.J. (2013). Plane non-steady-state problem of motion of the surface load on an elastic half-space. Mathematical Methods and Physicomechanical Fields, Lviv, 56, No.2, 157-163 (in Russian).
Kuznetsova E.L., Tarlakovsky D.V., Fedoten-kov G.J., Medvedsky A.L. (2013). Influence of non-stationary distributed load on the surface of the elastic layer. Works MAI, 71, 1-21 (in Russian).
Fedotenkov G.J., Tarlakovsky D.V., Vahter-ova Y.A. (2019). Identification of Non-stationary Load Upon Timoshenko Beam. Lobachevskii Journal of Mathematics, 40(4), 439-447.
Vahterova Y.A., Fedotenkov G.J. (2020). The inverse problem of recovering an unsteady line-ar load for an elastic rod of finite length. Journal of Applied Engineering Science, 18(4), 687-692, DOI:10.5937/jaes0-28073.
Gorshkov A.G., Tarlakovsky D.V. (1985). Dynamic contact problems with moving bound-aries. Nauka, Fizmatlit, 352 (in Russian).
Bogdanov V.R. (2018). Impact a circular cylin-der with a flat on an elastic layer. Transfer of Innovative Technologies, Vol.1, No.2, 68-74, DOI:10.31493/tit1812.0302.
Bogdanov V.R. (2012). The destruction toughness determination on the base of solution of three dimension problem in quasistatic plastic-elastic formulation. Bulletin of University of Lviv, Series Physics & Mathematics, No.76, 65-75 (in Ukrainian).
Mahnenko V.I. (1976). Computational methods for studying the kinetics of welding stresses and deformations. Naukova Dumka, Kiev, 320 (in Russian).
Mahnenko V.I. (2003). Improving methods for estimating the residual life of welded joints in long-life structures. Automatic welding, Kiev, No.10-11, 112-121 (in Russian).
Mahnenko V.I., Pozniakov V.D., Velikoiva-nenko E.A., Rozynka G.F., Pivtorak N.I. (2009). Risk of cold cracking when welding structural high-strength steels. Collection of sci-entific works Processing of materials in me-chanical engineering, National Shipbuilding University, No.3, 5-12 (in Russian).
Kachanov L.M. (1969). Fundamentals of the theory of plasticity. Nauka, Moscow, 420 (in Russian).
Collection: Theory of plasticity IL (1948). Moscow, 460 (іn Russian).
Hemming R.V. (1972). Numerical methods. Nauka, Moscow, 399 (in Russian).
Zukina E.L. (2004). Conservative difference schemes on non-uniform grids for a two-dimensional wave equation. Work of N.I. Lobachevski Math, Centre, Kazan, Vol.26, 151-160 (in Russian).
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2023 Vladislav Bogdanov
This work is licensed under a Creative Commons Attribution 4.0 International License.
Our journal abides by the CREATIVE COMMONS copyright rights and permissions for open access journals.
Authors, who are published in this journal, agree to the following conditions:
1. The authors reserve the right to authorship of the work and pass the first publication right of this work to the journal under the terms of a Creative Commons Attribution License, which allows others to freely distribute the published research with the obligatory reference to the authors of the original work and the first publication of the work in this journal.
2. The authors have the right to conclude separate supplement agreements that relate to non-exclusive work distribution in the form in which it has been published by the journal (for example, to upload the work to the online storage of the journal or publish it as part of a monograph), provided that the reference to the first publication of the work in this journal is included.
